Search Results

A porous plate sublimator (based on an existing Lunar Module LM-209 design) is baselined as a heat rejection device for the X-38 vehicle due to its simplicity, reliability, and flight readiness. The sublimator is a passive device used for rejecting heat to the vacuum of space by sublimating water to obtain efficient heat rejection in excess of 1,000 Btu/lb of water. It is ideally suited for the X-38/CRV mission as it requires no active control, has no moving parts, has 100% water usage efficiency, and is a well-proven technology. Two sublimators have been built and tested for the X-38 program, one of which will fly on the NASA V-201 space flight demonstrator vehicle in 2001. The units satisfied all X-38 requirements with margin and have demonstrated excellent performance. Minor design changes were made to the LM-209 design for improved manufacturability and parts obsolescence.

Technologies for the recycling of water are a primary goal of NASA’s advanced life support programs. Biological processes have been identified as an attractive method for wastewater processing. A fundamental new bioreactor based on a traditional activated sludge process is demonstrated that treats hygiene wastewater using magnetic iron oxide particles agglomerated with microbial cells. In this bioreactor, microbes are suspended in magnetic flocs in a wastewater medium. Instead of a traditional gravity separator used in activated sludge operations, a magnetic separator removes the microbial flocs from the outlet stream. The reactor separation operates continuously, independent of gravitational influences. The reactor has been able to simultaneously remove 98% of high levels of both nitrogenous and organic carbon impurities from the wastewater as well as achieve acceptably low levels of total suspended solids.

Twenty-nine recycled water, eight stored (ground-supplied) water, and twenty-eight humidity condensate samples were collected on board the Mir Space Station during the Phase One Program (1995-1998). These samples were analyzed to determine potability of the recycled and ground-supplied water, to support the development of water quality monitoring procedures and standards, and to assist in the development of water reclamation hardware. This paper describes and summarizes the results of these analyses and lists the lessons learned from this project. Results show that the recycled water and stored water on board Mir, in general, met NASA, Russian Space Agency (RSA), and U.S. Environmental Protection Agency (EPA) standards.

In bioregenerative life support systems, crop residues represent a source of biochemical energy for production of chemicals, pulp products and secondary foods. Hydrolysis of the structural carbohydrates in biomass produces edible glucose as well as various 5-carbon sugars usable by microorganisms. However, the biomass must be pretreated before hydrolysis to remove minerals useful as plant nutrients, break down lignin, and improve access of the enzymes to the carbohydrates. Some pre-treatments also hydrolyze part or all of the hemicellulose, leaving purified cellulose. For use in space, pretreatments must be safe, rapid and as complete as practicable. This paper will present a process comparison of three “space-compatible” pretreatment methods for lignocellu-losic crop residues from bioregenerative life support systems. Ozonation, alkaline hydrogen peroxide, and strong alkali treatment use only regenerable materials and mild processing conditions.

Poly (vinyl chloride) (PVC) matrix membranes which incorporate the ionophore nonactin have been evaluated as cation exchange membranes for ammonium ion transport in an electrolytic cell configuration. Interest exists for the development of cation selective membranes for removal of low levels (<200ppm) of ammonium ions commonly found in recycled effluent streams in such diverse applications as expected in a Space Station and commercial fisheries. Ammonium ions are generated as a decomposition product of urea and over time build up in concentration, thus rendering the water unsuitable for human consumption. Nonactin is commonly used in a PVC matrix for ion-selective electrodes.

This paper will describe the ISS TransHab’s architectural design being proposed as a habitation module for the International Space Station. TransHab is a space inflatable habitation module that originally was designed to support a crew of six as a transit habitat (TransHab) to and from Mars. As an evolution of TransHab, it has transformed into the proposed alternative habitat module for the International Space Station (ISS). A team of architects and engineers at the Johnson Space Center has been designing and testing this concept to make it a reality.

Design and Human Engineering (HE) processes strive to ensure that the human-machine interface is designed for optimal performance throughout the system life cycle. Each component can be tested and assessed independently to assure optimal performance, but it is not until full integration that the system and the inherent interactions between the system components can be assessed as a whole. HE processes, such as defining/applying requirements for human interaction with missions/systems, are included in space flight activities, but also need to be included in ground activities and specifically, ground facility testbeds such as the Bioregenerative Planetary Life Support Systems Test Complex (BIO-Plex). BIO-Plex is a self-contained living, working and crop-growth environment that may ultimately serve as a model for Mars surface habitation. The long duration nature of BIO-Plex brings the issue of habitability to the fore, making it tangible and testable.

Practical solar powered aircraft require an efficient energy storage system to store energy during the day for use at night. Hydrogen and oxygen, generated by electrolyzing water during the day and recombined at night to generate electricity, has a theoretical energy density of 3.73 kWh/kg. Harnessing this potential has been approached with a combination of a lightweight PEM electrolyzer and a lightweight PEM fuel cell with a new stack structure utilizing metallurgical bonding to assemble thin metal gas barriers with lightweight metal flow fields. This design minimizes size, weight, electrical resistance, and part count. This technology has been demonstrated to produce efficient and effective stacks.

The development of a Microsoft® Excel-compatible Environmental Control and Life Support System (ECLSS) Sizing Analysis “Tool” for conceptual design of Mars human exploration missions makes it possible for a user to choose different possible technologies in a corresponding subsystem. This tool estimates the mass, volume, and power requirements of technologies in a subsystem and the system as a whole. Furthermore, to verify that a design sized by the ECLSS Sizing Tool meets the mission requirements and integrates properly, a tabulated Integration Interface Module has been developed for quick referencing. Mass balance models that solve for component throughputs of ECLSS systems as the Water Recovery System (WRS) and Air Revitalization System (ARS) are being developed for the sizing of the subsystems. The ARS Mass Balance Model will be discussed in this paper.

The most recent goal of our research program was to identify the optimal features of each of three garments to maintain core temperature and comfort under intensive physical exertion. Four males and 2 females between the ages of 22 and 46 participated in this study. The garments evaluated were the MACS-Delphi, Russian Orlan, and NASA LCVG. Subjects were tested on different days in 2 different environmental chamber temperature/humidity conditions (24°C/H∼28%; 35°C/H∼20%). Each session consisted of stages of treadmill walking/running (250W to 700W at different stages) and rest. In general, the findings showed few consistent differences among the garments. The MACS-Delphi was better able to maintain subjects within a skin and core temperature comfort zone than was evident in the other garments as indicated by a lesser fluctuation in temperatures across physical exertion levels.

Humidity condensate collected and processed in-flight is an important component of a space station drinking water supply. Water recovery systems in general are designed to handle finite concentrations of specific chemical components. Previous analyses of condensate derived from spacecraft and ground sources showed considerable variation in composition. Consequently, an investigation was conducted to collect condensate on the Shuttle while the vehicle was docked to Mir, and return the condensate to Earth for testing. This scenario emulates an early ISS configuration during a Shuttle docking, because the atmospheres intermix during docking and the condensate composition should reflect that. During the STS-89 and STS-91 flights, a total volume of 50 liters of condensate was collected and returned. Inorganic and organic chemical analyses were performed on aliquots of the fluid.

The National Aeronautics and Space Administration (NASA) is interested in characterizing the responses of THOR (test device for human occupant restraint) anthropometric test device (ATD) to representative loading acceleration pulse s. Test conditions were selected both for their applicability to anticipated NASA landing scenarios, and for comparison to human volunteer data previously collected by the United States Air Force (USAF). THOR impact testing was conducted in the fore-to-aft frontal (-x) and in the upward spinal (-z) directions with peak sled accelerations ranging from 8 to 12 G and rise times of 40, 70, and 100ms. Each test condition was paired with historical huma n data sets under similar test conditions that were also conducted on the Horizontal Impulse Accelerator (HIA). A correlation score was calculated for each THOR to human comparison using CORA (CORrelation and Analysis) software.

This paper describes the need and solution for minimizing EVA airlock time and depress gas losses using a new method that minimizes EVA out-the-door time for a suited astronaut and reclaims most of the airlock depress gas. This method consists of one or more related concepts that use an evacuated reservoir tank to store and reclaim the airlock depress gas. The evacuated tank can be an inflatable tank, a spent fuel tank from a lunar lander descent stage, or a backup airlock. During EVA airlock operations, the airlock and reservoir would be equalized at some low pressure, and through proper selection of reservoir size, most of the depress gas would be stored in the reservoir for later reclamation. The benefit of this method is directly applicable to long duration lunar and Mars missions that require multiple EVA missions (up to 100, two-person lunar EVAs) and conservation of consumables, including depress pump power and depress gas.

The Orion crew module (CM) is being designed to perform survivable land and water landings. There are many issues associated with post-landing crew survival. In general, the most challenging of the realistic Orion landing scenarios from an environmental control standpoint is the off-nominal water landing. Available power and other consumables will be very limited after landing, and it may not be possible to provide full environmental control within the crew cabin for very long after splashdown. Given the bulk and thermal insulation characteristics of the crew-worn pressure suits, landing in a warm tropical ocean area would pose a risk to crew survival from elevated core body temperatures, if for some reason the crewmembers were not able to remove their suits and/or exit the vehicle. This paper summarizes the analyses performed and conclusions reached regarding post-landing crew survival following a water landing, from the standpoint of the crew's core body temperatures.

Effective helmet performance is a critical component to achieving safe and efficient missions along the entire timeline; from launch and entry events to operations in a micro-gravity environment to exploration of a planetary surface, the helmet system is the capstone of the pressurized space suit assembly. Each phase of a mission requires uncompromising protection in the form of a robust pressure vessel and adequate protection from impact, both interior and exterior, all while remaining relatively comfortable and providing excellent visual interaction with the environment. Historically there have been large voids between these critical characteristics with the primary focus concerning the pressure vessel first and impact protection and crew comfort second. ILC Dover, NASA-JSC, Gentex Corporation, and Hamilton Sundstrand formed an Integrated Product Team (IPT) and conducted a NASA funded study to research and evaluate new concepts in helmet design.

The Sublimator Driven Coldplate is a unique piece of thermal control hardware that has several advantages over a traditional thermal control scheme. The principal advantage is the possible elimination of a pumped fluid loop, potentially saving mass, power, and complexity. Because this concept relies on evaporative heat rejection techniques, it is primarily useful for short mission durations. Additionally, the concept requires a conductive path between the heat-generating component and the heat rejection device. Therefore, it is mostly a relevant solution for a vehicle with a relatively low heat rejection requirement. This paper describes the design of an engineering development unit intended to demonstrate the feasibility of the Sublimator Driven Coldplate concept.

This paper addresses the development of a novel technology to simultaneously reduce total organic carbon (TOC) and microbial count (MC) in biological water processor (BWP) processed water. This approach also creates a biocidal environment in BWP processed water before being fed into the reverse osmosis (RO) and post processing systems. The technology is based on an advanced oxidation process using an on-demand oxidizer generator, which does not require consumable chemicals. The SBIR (Small Business Innovation Research) Phase I feasibility studies successfully demonstrated the process efficacy in the reduction of both TOC and MC of the BWP effluent. Also, the residual disinfectant and reduced TOC in the treated effluent minimized fouling the RO membrane and water lines. In the Phase II project, a prototype is being fabricated and evaluated for its ability to reduce TOC and MC, and extend RO membrane life.

Future spacesuits will require thermal insulation protection in low-earth orbit (LEO), in the near-earth neighborhood and in planetary environments. In order to satisfy all future exploration needs and lower production and maintenance costs, a common thermal insulation is desirable that will perform well in all these environments. A highly promising material is a fiber-reinforced aerogel composite insulation currently being developed at the Johnson Space Center. This paper presents an overview of aerogels and their manufacture, a summary of the development of a flexible fiber-based aerogel for NASA by Aspen Aerogels, Inc., and performance data of aerogels relative to flexible commercial insulation. Finally, future plans are presented of how an aerogel-based insulation may be integrated into a spacesuit for ground testing as well as for a flight configuration.

Flexible fiber-reinforced aerogel composites were studied for use as insulation materials of a future space suit for Moon and Mars exploration. High flexibility and good thermal insulation properties of fiber-reinforced silica aerogel composites at both high and low vacuum conditions make it a promising insulation candidate for the space suit application. This paper first presents the results of a durability (mechanical cycling) study of these aerogels composites in the context of retaining their thermal performance. The study shows that some of these Aerogels materials retained most of their insulation performance after up to 250,000 cycles of mechanical flex cycling. This paper also examines the problem of integrating these flexible aerogel composites into the current space suit elements.